Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME

WHITE KNIGHT COLD GAL AEROSOL

NFPA

PRODUCT USE

One pack zinc rich spray anti- corrosive primer paint for " cold galvanizing" and
corrosion protection of ferrous metals. Application is by spray atomization from a hand
held aerosol pack.

SYNONYMS

"Zinc Rich Aerosol Paint", "cold galvanising"

Section 2 - HAZARDS IDENTIFICATION

CANADIAN WHMIS SYMBOLS

EMERGENCY OVERVIEW

RISK

Possible risk of harm to the unborn child.
Harmful by inhalation and if swallowed.
Irritating to eyes, respiratory system and skin.
Extremely flammable.
Very toxic to aquatic organisms, may cause long- term adverse effects in the
aquatic environment.
Risk of explosion if heated under confinement.

POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED

  Accidental ingestion of the material may be harmful; animal experiments indicate that ingestion of less than 150 gram may be fatal or may produce serious damage to the health of the individual.  Overexposure is unlikely in this form.  Ingestion may result in nausea, pain, vomiting. Vomit entering the lungs by aspiration may cause potentially lethal chemical pneumonitis.  Considered an unlikely route of entry in commercial/industrial environments.  

EYE

  This material can cause eye irritation and damage in some persons.  The liquid produces a high level of eye discomfort and is capable of causing pain and severe conjunctivitis. Corneal injury may develop, with possible permanent impairment of vision, if not promptly and adequately treated.  

SKIN

  This material can cause inflammation of the skin oncontact in some persons.  Skin contact is not thought to have harmful health effects, however the material may still produce health damage following entry through wounds, lesions or abrasions.  The material may accentuate any pre-existing skin condition.  Toxic effects may result from skin absorption.  Exposure limits with "skin" notation indicate that vapor and liquid may be absorbed through intact skin. Absorption by skin may readily exceed vapor inhalation exposure. Symptoms for skin absorption are the same as for inhalation. Contact with eyes and mucous membranes may also contribute to overall exposure and may also invalidate the exposure standard.  Bare unprotected skin should not be exposed to this material.  The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, the production of vesicles, scaling and thickening of the skin.  

INHALED

  If inhaled, this material can irritate the throat andlungs of some persons.  Inhalation hazard is increased at higher temperatures.  Inhalation exposure may cause susceptible individuals to show change in heart beat rhythm i.e. cardiac arrhythmia. Exposures must be terminated.  Inhalation of high concentrations of gas/vapor causes lung irritation with coughing and nausea, central nervous depression with headache and dizziness, slowing of reflexes, fatigue and inco-ordination.  If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and possible death.  Inhalation of vapor may aggravate a pre-existing respiratory condition.  WARNING: Intentional misuse by concentrating/inhaling contents may be lethal.  

CHRONIC HEALTH EFFECTS

  Principal routes of exposure are usually by inhalation of vapor/spray mist, inhalation of vapor and skin contact/absorption.  Anesthetics and narcotic effects (with dulling of senses and odor fatigue) are a consequence of exposure to chlorinated solvents.  Individual response varies widely; odor may not be considered objectionable at levels which quickly induce central nervous system effects. High vapor concentrations may give a feeling of euphoria. This may result in reduced responses, followed by rapid onset of unconsciousness, possible respiratory arrest and death.  Chronic solvent inhalation exposures may result in nervous system impairment and liver and blood changes. [PATTYS].  Prolonged or continuous skin contact with the liquid may cause defatting with drying, cracking, irritation and dermatitis following.  WARNING: Aerosol containers may present pressure related hazards.  Welding or flame cutting of metals with zinc or zinc dust coatings may result in inhalation of zinc oxide fume; high concentrations of zinc oxide fume may result in "metal fume fever"; also known as "brass chills", an industrial disease of short duration. [I.L.O] Symptoms include malaise, fever, weakness, nausea and may appear quickly if operations occur in enclosed or poorly ventilated areas.