Section 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME

VALSPAR MIL-P-24441 PRIMER CURING SOLUTION

NFPA

PRODUCT USE

Hardener or Part B of a 2 pack epoxy coating system. Requires that the two parts be mixed
by hand or mixer before use, in accordance with manufacturers directions. Mix only as much
as is required. Do not return the mixed material to the original containers. Application
is usually by spray atomisation in a ventilated spray booth, after viscosity reduction
with thinner.

SYNONYMS

"polyamine curing", "agent epoxy system"

Section 2 - HAZARDS IDENTIFICATION

CANADIAN WHMIS SYMBOLS

EMERGENCY OVERVIEW

RISK

Harmful if swallowed.
Irritating to skin.
Risk of serious damage to eyes.
Possible risk of harm to the unborn child.
HARMFUL - May cause lung damage if swallowed.
Harmful: danger of serious damage to health by prolonged exposure through
inhalation.
Highly flammable.
Vapors may cause dizziness or suffocation.

POTENTIAL HEALTH EFFECTS

ACUTE HEALTH EFFECTS

SWALLOWED

  Accidental ingestion of the material may be harmful; animal experiments indicate that ingestion of less than 150 gram may be fatal or may produce serious damage to the health of the individual.  Considered an unlikely route of entry in commercial/industrial environments.  Ingestion may result in nausea, pain, vomiting. Vomit entering the lungs by aspiration may cause potentially lethal chemical pneumonitis.  

EYE

  If applied to the eyes, this material causes severe eye damage.  The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis.  

SKIN

  This material can cause inflammation of the skin oncontact in some persons.  Skin contact is not thought to have harmful health effects, however the material may still produce health damage following entry through wounds, lesions or abrasions.  Epoxy materials may cause allergic and/or contact dermatitis responses, which may occur on exposure or may become apparent only after repeated exposures. Sensitization is possible. Photoallergic dermatitis may result from contact with the material. This type of response can be elicited only in individuals who have been previously allergically sensitized to the chemical agent and appropriate radiation. Photoallergic dermatitis presents, clinically, as an eczematous dermatitis in sun-exposed areas.  The material may cause skin irritation after prolonged or repeated exposure and may produce on contact skin redness, swelling, the production of vesicles, scaling and thickening of the skin.  

INHALED

  Inhalation may produce health damage*.  The material is not thought to produce respiratory irritation (as classified using animal models). Nevertheless inhalation of the material, especially for prolonged periods, may produce respiratory discomfort and occasionally, distress.  Inhalation hazard is increased at higher temperatures.  Inhalation of high concentrations of gas/vapor causes lung irritation with coughing and nausea, central nervous depression with headache and dizziness, slowing of reflexes, fatigue and inco-ordination.  If exposure to highly concentrated solvent atmosphere is prolonged this may lead to narcosis, unconsciousness, even coma and possible death.  

CHRONIC HEALTH EFFECTS

  There is some evidence that inhaling this product is more likely to cause a sensitization reaction in some persons compared to the general population.  

  Principal routes of exposure are usually by skin contact/absorption and inhalation of vapor.  Chronic solvent inhalation exposures may result in nervous system impairment and liver and blood changes. [PATTYS].  Sensitization reactions may appear suddenly after repeatedsymptom free exposures.  Sensitization may give severe responses to very low levels of exposure, i.e. hypersensitivity. Sensitized persons should not be allowed to work in situations where exposure may occur.  Prolonged or continuous skin contact with the liquid may cause defatting with drying, cracking, irritation and dermatitis following.  As with any chemical product, contact with unprotected bare skin; inhalation of vapor, mist or dust in work place atmosphere; or ingestion in any form, should be avoided by observing good occupational work practice.